+353-1-416-8900REST OF WORLD
+44-20-3973-8888REST OF WORLD
1-917-300-0470EAST COAST U.S
1-800-526-8630U.S. (TOLL FREE)

Pharmaceutical Engineering: A Primer for Advanced Process Development. Volume 2: Solid Dosage form Process Design

  • Book

  • April 2025
  • Elsevier Science and Technology
  • ID: 5954953

Pharmaceutical Engineering: A Primer for Advanced Process Development. Volume Two: Solid Dosage form Process Design provides a comprehensive, engineering-focused description of pharmaceutical dosage form process development and manufacturing. The set is split into two volumes where Volume One focuses on liquids and Volume Two on solids. Each volume introduces the most commonly used manufacturing processes for pharmaceutical dosage forms and addresses critical formulation and process parameters that influence drug product process performance and product quality. This is supplemented with detailed descriptions of engineering models as well as tools that can be used to support their development and verification (such as process analytical technology (PAT)) as well as the appropriate utilization of process and equipment knowledge. Typical scale-up challenges inspired by real industrial examples will be presented as well as a review of the latest correlations, theories and models that can form the basis for science-based scale-ups and transfers.

Table of Contents

Section 1: The Basics 1. Introduction (Noor Al-Rifai, Ashish Kumar and Rene Holm) 2. General introduction to the field of drug product design and development, including current challenges and recent trends. 3. Regulatory considerations for pharmaceutical process development (Rene Holm) 4. A description of ICH Q8 (R2) in the relevant context, including process requirements, QbD options and experimental/computational approaches, as well as a description of pharmaceutical process validation. 5. Engineering fundamentals 6. The basic components needed to understand and build an engineering approach to a pharmaceutical drug product process, including and not limited to: material and energy balances, heat and mass transfer, dimensional analysis, flow of fluids and powders, scale-up approaches and workflows. This will be an introductory chapter and will be covered in more detail in section 2. 7. In process analysis (Jukka Rantanen, KU) 8. A description of some of the general analytical options that can be used for experimental characterization of drug product processes and the link to subsequent chapters, including the PAT regulatory status. The analytical principles behind common measurements across the different unit operations will be presented here. Section 2: Unit Operations 9. Mixing of solids (Eric Maynard Jenike & Johanson; Richard Elkes GSK) 10. Dry milling (Michael Juhnke Novartis; Arno Kwade TU Braunschweig; Ecevit Bilgili NJYT) 11. Granulation (Stephen Sirabian Glatt) 12. Roller compaction (Richard Elkes GSK) 13. High shear granulation 14. Fluid bed granulation 15. Hot melt granulation 16. Extrusion and spheronisation 17. Drying fluid bed or pan (Krist Gernaey Danish Technical University) 18. Spray drying (Sune Andersen Janssen; Hovione; Reinhard Vehring University of Alberta; Andrey Bayly University of Leeds) 19. Tabletting (Ashisk Kumar Ghent University/Janssen; Richard Elkes GSK) 20. Film coating of tablets fluid bed or pan (Martin de Juan AZ) 21. Capsule filling powder (Eva Faulhammer Research Center Pharmaceutical Engineering, Graz) 22. Continuous Manufacturing (Ashish Kumar Ghent University / Janssen)

Authors

Ren� Holm Scientific Director and University Professor Department of Physics, Chemistry and Pharmacy University of Southern Denmark, Denmark. Ren� Holm received his pharmaceutical training at the Royal Danish School of Pharmacy, now the school of pharmacy at University of Copenhagen, Denmark, in 1998 and his PhD in biopharmaceutics from the same institution in 2002. Dr. Holm joined Lundbeck in 2001 and changed to Janssen in 2016. Dr. Holm has worked within pharmaceutical development and the associated process development, developability in drug discovery, physical chemistry and material science covering both small and large molecules. As of 2021 Dr. Holm have been a full professor in Pharmaceutical physical chemistry at the university of Southern Denmark. Dr. Holm is (co-) author of more than 230 original articles in peer-reviewed journals and patents in the field of biopharmaceutics, preformulation, formulation and physical pharmacy and is an honorary professor in physical chemistry at the Department of Science and Environment, University of Roskilde, Denmark Noor Al-Rifai Senior Scientist Department of Chemical Engineering University College London (UCL) London, UK. Noor Al-Rifai is a senior scientist at The Janssen Pharmaceutical Companies of Johnson & Johnson within small molecule drug product development - process engineering. Dr Al-Rifai graduated from the University of Birmingham with an MEng in chemical engineering with business management (2009) and from UCL with a PhD in micro-reaction engineering (2016). Dr Al-Rifai's professional experience spans pharmaceutical and consumer goods product and process development - Merck Sharp & Dohme (2009-2010), Procter & Gamble (2016-2018) and currently Janssen/Johnson & Johnson (2018-Present). At Janssen, Dr Al-Rifai is delivering on engineering strategies to optimise and accelerate product, process development and technology transfer. Dr Al-Rifai is a Chartered Engineer by the Engineering Council/Institution of Chemical Engineers (CEng) and Fellow of the Higher Education Academy (FHEA), the latter gained in her role as Teaching Fellow at UCL Chemical Engineering (2014-2016). Ashish Kumar Principal Scientist and University Professor, Pharmaceutical Engineering Research Gro,up, Ghent University , Ghent, Belgium. Ashish Kumar is Assistant Professor for Pharmaceutical Engineering at Ghent University, Belgium. With his mathematical modeling and simulation background, Dr. Kumar is leading a team involved in the research and development of detailed mechanistic and data-driven frameworks to predict key quality attributes for pharmaceutical processes. His current areas of interest are in understanding constitutive mechanisms that influence the drug processing during manufacturing and hence its performance in the patient to streamline the development processes, which can support the risk-based decision-making paradigms and get products faster to market. Dr. Kumar also holds the Principal Scientist - Process Engineering position in the Drug product development division of Janssen Pharmaceutica, Belgium, where he is actively involved in developing continuous manufacturing processes for solid dosage forms.